Microcom AD 2730 Guia do Utilizador Página 1

Microcom AD 2730 (2735) ADSL 2/2+ WiFi router User Guide

• Bridge Tap Mitigation support • ATM Layer with Traffic shaping QoS Support (UBR, CBR, VBR-rt, VBR-nrt) • Multiple PVC up to 8 support (Bridge Su

• Web Based Firmware Upgrade (Local) UI • Telnet/CLI (Read Only) log Support e feature enhancement Security Su• Stateful Packet Inspection Suppor

Chapter 3 - Your Gateway At A Glance The ADSL Ethernet & USB Combo may have different ports and LEDs. Let’s take a look at the different options

Chapter 4 - Installing The ADSL Router 1. . For connections to the Ethernet and DSL interfaces, please refer to the easy start guide. 2. Connect th

Chapter 5 - Setting Up the ADSL Router (Basic Mode) The basic tabs consist of features which are catered for basic users. will guide you through you

Figure 1-4 : Basic Home Screen Quick Start By default the ADSL Router has being configured to PPP connection and user is only required to enterthe u

5.3 LAN / DHCP Configuration On one side of your ADSL Router, you have your own Local Area network (LAN) connections. This is where you plug in your

5.4 Diagnostic Test Diagnostic Test is used for investigating whether the ADSL Router is properly connected to the WAN Netw your conork. See Fig 1-

Figure 1-8 : Ping Test Screen Wireless 5.5.1 Wireless Setup 5.5 The SSID default which is defaulte anged. SSID is wireless network name for the

5.5.2 Wireless Configuration For users who want to explore the advanced features, you can click on the Advance button. The options listed can be c

Microcom AD 2730, AD 2735 User’s Guide Table of Contents Preliminary Pages Page 1.1 Introduction...

In order to implement security, proceed with the following steps. See Fig 1-12 1. Select the WEP option. 2. Check on “Enable WEP Wireless Security”

WPA which stands for WiFi Protected Access. WPA is an industry-supported, pre-standard version of 802.11i utilizing the Temporal Key Integrity Protoc

5.6 Advanced This mode is catered for advance users, a brief explanation of the links are listed as shown below. Figure 1-16 : Advance Screen 5.6

Figure 1-17 : New Connection (PPPOE Connection Setup) 5.6.3 ADSL Modulation To configure the DSL modulation type, Click setup. Under WAN Setup, s

To configure the gateway for PPPoE, click on Setup and then click on New Connection. The default PPPoE connection setup is displayed. At the Type f

5.6.5 LAN Configuration You can change the ADSL Router’s IP address by, clicking Setup and under LAN Setup, select LAN Configuration, then click Co

Figure 1-21 : LAN Clients 5.6.7 Ethernet Switch Configuration The IGMP Snooping prevents the switch from flooding the LAN ports with multicast fr

5.6.8 Application (UPnP) UPnP NAT and Firewall Traversal allow traffic to pass-thru the ADSL Router for applications using the UPnP protocol. This f

8. Time Zone - The time zone of the router. 9. Day Light - Check/uncheck this option to enable/disable day light saving. See Fig 1-24 Figure 1-24

5.6.11 Routing (Static Routing) If the ADSL Router is connected to more than one network, you may need to set up a static route between them. A stat

5.6.14 System Password... 5-30 5.6.15 Firmware Upgrade...

See Fig 1-27 Figure 1-27 : Dynamic Routing 5.6.13 Routing Table Routing Table shows the information used by routers when making packet forwarding

Figure 1-29 : System Password 5.6.15 Firmware Upgrade You can upgrade the ADSL Router’s firmware, clicking on Update Gateway under the Tools page

5.6.16 Restore to Default The restore to factory defaults feature will set the ADSL Router to its factory default configuration by resetting the ADS

Figure 1-33 : IP Filters 5.7.2 LAN Isolation LAN isolation allows you to disable the flow of packets between up to three-user-defined LAN groups (

Figure 1-35 : URL Filters 5.8 Status This status section allows users to view the following connections and interfaces: • Connection Status • Sys

5.8.1 Connection Status Connection Status will display all the relevant information regarding your Internet Connection, it will display the type of

5.8.3 Remote Log Settings This feature is for users to enable remote logging. Settings mentioned below are essential for this feature to work: • Lo

Figure 1-41 : DHCP Clients 5.8.6 Modem Status This screen will display the Modem status and DSL statistics. Figure 1-42 : Modem Status 5.8.7 Pr

Figure 1-43 : Product Information 5.9 Help The Help screen takes you to the different Help Sections for Firewall, Bridge Filters, LAN Clients, LAN

List of Illustrations Figure Page Figure 1-1 : Wireless-G System Configuration Diagram...

Figure 1-28 : Routing Table... 5-30 Figure 1-

Declaration Of Conformity Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the Europe

Modifications made to the product, unless expressly approved by the party responsible, could void the user’s right to operate the equipment. RF Expos

Chapter 1 - About this Manual 1.1 Introduction neral product overview and description of its subsystems and components and tenance instructions of t

Chapter 2 – ADSL Router Description The ADSL 2/2+ Ready Wireless LAN 802.11g 4 Port Ethernet & USB Combo 4 Port Router is a high-speed WAN bridg